Indiana BMV CDL General Knowledge Practice Test 2
Test 2 of 5. Pick an answer for each question to see if it is right and why; your score appears at the end. You need 40 correct answers to pass, the same ratio as the real Indiana test.
- Questions50
- Correct to pass40
- Passing score80%
- Minimum age18 years
-
1. Apart from the risk of stalling, why is rolling backwards when starting on an upgrade so serious in a heavy vehicle?
Show answer
Answer D: You can strike the vehicle behind you, which is often much closer than you think
You cannot see how close the vehicle behind has stopped, and even a short roll back is enough to hit it.
-
2. On the Interstate System, what is the federal maximum weight allowed on a single axle?
Show answer
Answer A: 20,000 pounds
Federal limits for the Interstate System cap one single axle at 20,000 pounds.
-
3. Why does a load of live animals need special attention?
Show answer
Answer D: The animals move and lean, so the center of gravity shifts and the vehicle can be pushed off balance in a turn
A live load will not stay where it is put, and that movement changes the balance of the vehicle exactly when a curve is loading it most.
-
4. What extinguisher rating is required on a vehicle carrying hazardous materials in amounts that need placards?
Show answer
Answer B: 10 B:C or more
Placarded loads carry a much higher fire risk, so the required extinguisher rating rises to at least 10 B:C.
-
5. You are loading a flatbed that has no sides or bulkheads. How must the cargo be held?
Show answer
Answer D: By tiedowns, blocking or bracing, since there are no walls to keep it from shifting or falling off
Open decks depend entirely on securement devices; every article must be tied down or otherwise immobilized so it cannot move, spill or fall.
-
6. Why must tiedowns be rechecked during a trip even when they were tight at the start?
Show answer
Answer C: Road vibration and cargo movement can loosen them as the miles go by
Straps and chains settle and loosen as the vehicle bounces and the cargo shifts slightly, so the load must be rechecked at the required intervals.
-
7. You are drifting in the lane, yawning constantly and cannot remember the last few miles. What is the only reliable cure?
Show answer
Answer C: Stopping in a safe place and sleeping
Those are classic drowsiness warning signs, and nothing except sleep repays the sleep the body is missing.
-
8. A dispatcher tells you to take a trailer you believe is loaded badly enough to be unsafe. What should you do?
Show answer
Answer C: Refuse to move it until the load has been made safe
The driver may not operate a vehicle whose cargo is not properly distributed and secured, and an instruction from an employer does not change that.
-
9. Why must you never coast down a hill in neutral or with the clutch pushed in?
Show answer
Answer C: You lose the braking effect of the engine and your brakes may overheat and fail
Engine braking is what keeps a heavy vehicle in check on a grade; coasting throws it away and leaves the service brakes to do all the work until they overheat.
-
10. You need to pull off onto the shoulder because of a problem with the load. How should you communicate that to other drivers?
Show answer
Answer D: Signal the move, then switch on the four-way flashers once stopped
Other drivers need a signal before you leave the lane and a clear warning once the vehicle is stopped near the traffic lanes.
-
11. How are the headlights, marker lights and turn signals checked during the seven-step inspection?
Show answer
Answer A: The engine is shut off, the parking brake is set, the lights are switched on and then checked from outside the vehicle
The lights are switched on with the vehicle secured, then the driver walks around and confirms each lamp actually works and is clean.
-
12. What tells a driver when to shift up in a vehicle with a manual transmission?
Show answer
Answer C: Engine speed in rpm together with road speed
Shift points are judged from engine rpm and road speed, using the operating range the manufacturer specifies for that engine.
-
13. Which factors determine a safe speed for a long, steep downgrade?
Show answer
Answer C: The steepness and length of the grade, the weight of the vehicle and cargo, and the road and weather conditions
Gravity, weight and traction all decide how fast a heavy vehicle can safely descend, which is why signs often post lower speeds for trucks on grades.
-
14. Your brakes have failed on a downgrade and there is no escape ramp in sight. What is the best choice?
Show answer
Answer A: Steer into an open field or onto a side road that flattens out or climbs uphill
A flat or uphill escape route uses gravity and rolling resistance to stop the vehicle; take it as soon as you see it, because the longer you wait the faster you go.
-
15. A dock crew loads all of the freight at the very back of a 48 foot van trailer. What are the two consequences?
Show answer
Answer A: The steering axle is relieved of weight and steering becomes light, and the trailer axles may go over the limit
Weight placed far to the rear lifts weight off the front of the combination, so the steering goes light while the trailer axles take too much of the load.
-
16. Why is a sudden, sharp lane change dangerous in a loaded heavy vehicle?
Show answer
Answer D: The vehicle can lean far enough to roll over, especially when the load sits high
A quick swerve throws the weight of a tall, heavy load sideways, and a rollover can begin before the tires ever slide.
-
17. Why do cracked spring hangers or badly worn shackles matter?
Show answer
Answer A: They allow the axle to shift out of its correct position under the vehicle
Hangers and shackles hold the spring, and therefore the axle, in place, so when they fail the axle can move and the vehicle may become uncontrollable.
-
18. Why should high beams not be used in fog?
Show answer
Answer A: The light reflects back off the droplets and blinds you
Fog is made of water droplets that scatter light straight back at the driver, so a stronger beam makes the wall of glare worse rather than better.
-
19. What is the minimum age to apply for an Indiana Commercial Learner's Permit or Commercial Driver's License?
Show answer
Answer A: 18 years old
Indiana requires an applicant to be at least 18 years of age to apply for a Commercial Learner's Permit or a Commercial Driver's License.
-
20. You have stopped and a pedestrian is waiting to cross in front of your truck. Why should you not wave the person across?
Show answer
Answer C: Another driver may not stop, and your wave sends the person into danger
You cannot control what drivers in the other lanes will do, so you should not invite a pedestrian into a lane you do not command.
-
21. How do you test for leaks in a hydraulic brake system during the pre-trip inspection?
Show answer
Answer A: Pump the pedal three times, then hold firm pressure for five seconds and make sure the pedal does not move
If the pedal sinks while you hold pressure, fluid is escaping or air is in the lines, and the vehicle must not be driven until the problem is repaired.
-
22. In very hot weather, how often should you check the tires during a trip?
Show answer
Answer D: About every two hours or every 100 miles
Heat raises tire pressure and can lead to blowouts, so tires are checked about every two hours or 100 miles when it is very hot.
-
23. You are pulling away from a curb in a 65 foot combination. Besides traffic, what must you watch?
Show answer
Answer B: The trailer wheels, which stay close to the curb and can strike it or an object on it
Because of off-tracking, the rear wheels follow a tighter path than the front, so they stay near the curb while the cab is already out in the lane.
-
24. What is the purpose of an escape ramp on a mountain grade?
Show answer
Answer C: To stop a runaway vehicle without injuring the driver
Escape ramps use soft material or a steep upgrade to bring a vehicle with failed brakes to a controlled stop.
-
25. How can a driver tell that a shipment includes hazardous materials?
Show answer
Answer B: The shipping paper describes them and the packages carry hazard warning labels
Hazardous materials are identified on the shipping paper with their shipping name and hazard class, and the packages themselves carry labels showing the hazard.
-
26. An oncoming vehicle drifts across the center line into your lane. What is usually the safest move?
Show answer
Answer C: Steer to the right, toward the shoulder if necessary
Moving right keeps you away from the drifting vehicle and off the oncoming side; the other driver may swerve back and hit you if you go left.
-
27. What speed and gear should be used when backing a large vehicle?
Show answer
Answer B: As slowly as possible, in the lowest reverse gear
Backing slowly in the lowest reverse gear keeps the vehicle under precise control and leaves time to correct the path.
-
28. You are making a right turn and cannot complete it without swinging into the oncoming lane. An oncoming car is approaching. What should you do?
Show answer
Answer A: Wait and let the oncoming vehicle pass before completing the turn, and do not back up
The oncoming vehicle has the lane; backing up in traffic is dangerous, so hold your position and finish the turn once the way is clear.
-
29. You are stopped in traffic on a steep upgrade behind another truck. How much space should you leave in front?
Show answer
Answer A: Enough that you can pull away without rolling back into the vehicle behind you
Room ahead lets you get moving smoothly on a grade instead of having to hold the vehicle perfectly still or roll back toward the traffic behind.
-
30. You are about to slow down sharply on a highway to make a turn into a narrow driveway. How can you warn the drivers behind you?
Show answer
Answer C: Tap the brake pedal a few times so the brake lights flash before you slow down
A few light taps flash the brake lights and give following drivers an early warning that you are about to slow or stop.
-
31. You find a defect during the pre-trip inspection. What must happen before the vehicle is driven?
Show answer
Answer C: It must be repaired, or the vehicle must not be driven
Writing a defect down does not make the vehicle safe; a defect that affects safe operation has to be corrected before the trip starts.
-
32. What is the most common cause of a front-wheel skid, where the vehicle keeps going straight even though you turn the wheel?
Show answer
Answer B: Driving too fast for the conditions
A front-wheel skid usually comes from too much speed for the traction available; the only cure is to let the vehicle slow down and stop turning or braking so hard.
-
33. You are on a freeway and see brake lights come on in several vehicles far ahead of you. What should you do?
Show answer
Answer A: Ease off the accelerator and get ready to slow down
Brake lights well ahead are an early warning that traffic is slowing, and acting on them gives a heavy vehicle the room it needs.
-
34. At 55 mph, about how far does a vehicle travel during a typical 3/4 second perception time plus 3/4 second reaction time, before the brakes even begin to work?
Show answer
Answer C: About 120 feet
Each 3/4 second at 55 mph covers about 60 feet, so perception and reaction together use up roughly 120 feet before braking starts.
-
35. Two vehicles of exactly the same length make a right turn, one gently and one very tightly. What is the effect on off-tracking?
Show answer
Answer A: Turning more sharply increases off-tracking, so the tight turn needs more room
Off-tracking depends on both the length of the vehicle and the sharpness of the turn; a tighter corner brings the rear wheels further inside the path of the front wheels.
-
36. Total stopping distance is made up of which parts?
Show answer
Answer A: Perception distance, reaction distance and braking distance
The vehicle travels while the hazard is recognized, while the driver moves to the pedal, and again while the brakes slow the vehicle.
-
37. Some commodities have their own detailed securement rules on top of the general ones. Which list is made up of such commodities?
Show answer
Answer C: Logs, metal coils, paper rolls, concrete pipe and crushed vehicles
The cargo securement rules add specific requirements for particular commodities, including logs, dressed lumber, metal coils, paper rolls, concrete pipe, intermodal containers, vehicles, crushed cars, roll on containers and large boulders.
-
38. What is the correct way to test the parking brake before a trip?
Show answer
Answer C: With the parking brake set, put the vehicle in a low gear and gently try to move forward
A parking brake that holds against a gentle pull in low gear is working; if the vehicle moves, the brake needs adjustment or repair.
-
39. What does the federal bridge formula do?
Show answer
Answer C: It reduces the weight allowed on a group of axles as those axles get closer together
Axles bunched together concentrate the load on a short span of a bridge, so the formula lowers the allowable weight as the spacing shrinks.
-
40. Why should a driver avoid shifting gears in the middle of a turn at an intersection?
Show answer
Answer D: Shifting during the turn takes a hand off the wheel and can cost you control
Pick the gear before you begin turning; shifting in the turn removes a hand from the wheel and can interrupt power just when you need steady control.
-
41. Besides slowing down, which technique most reduces the risk of a skid on a snow covered road?
Show answer
Answer B: Make every steering, braking and speed change gradual
Traction is limited on snow, and sudden inputs demand more grip than the surface can supply, so smoothness is what keeps the tires attached to the road.
-
42. Under federal safety rules, what must the driver of a commercial vehicle do before starting a trip?
Show answer
Answer A: Be satisfied that the vehicle is in safe operating condition
The driver is responsible for inspecting the vehicle and must be satisfied it is in safe operating condition before the trip begins.
-
43. After coupling, where should the fifth wheel release handle be?
Show answer
Answer A: In the locked position with the safety latch in place
The handle must be pushed in and latched, because a handle left out means the jaws can open and release the trailer while you are driving.
-
44. A vehicle becomes unsafe while you are already on the road. What does the federal rule allow?
Show answer
Answer A: Continuing only to the nearest place where repairs can safely be made
If stopping where you are would be more dangerous than moving, the rule allows you to reach the nearest place where the vehicle can safely be repaired, and no further.
-
45. What maximum speed does Indiana set for a school bus that is not on an interstate or state highway?
Show answer
Answer B: 40 miles per hour, or the posted limit if it is lower
Indiana caps a school bus at 40 miles per hour when it is not on an interstate or state highway, and at 60 miles per hour or the posted limit when it is.
-
46. You are moving an oversized load under a permit that requires a pilot vehicle. What is the pilot vehicle there to do?
Show answer
Answer B: Warn other traffic and check the route ahead for clearances and hazards
Escort or pilot vehicles warn approaching traffic and scout the route for low bridges, narrow spots and other hazards that a wide or long load cannot pass.
-
47. You have countersteered to correct a rear-wheel skid and the vehicle straightens out. What must you be ready for next?
Show answer
Answer D: The vehicle may swing back the other way, so you must steer again to correct it
A vehicle coming out of a skid tends to overshoot and swing in the opposite direction, and the driver must be ready to countersteer a second time.
-
48. Under federal rules, what happens to a commercial driver found with any detectable amount of alcohol while operating a commercial vehicle?
Show answer
Answer D: The driver is placed out of service for 24 hours
Any measurable alcohol takes a commercial driver off the road for 24 hours, and a concentration of 0.04 percent or more brings a disqualification.
-
49. During a stop you find a package in the trailer leaking an unknown chemical. What should you do?
Show answer
Answer C: Keep clear, keep others away and get help without touching the package
A driver without the training and equipment does not handle a leak; the job is to protect people from the material and get qualified help to the scene.
-
50. What color must the clearance and side marker lamps and reflectors at the front of a trailer be?
Show answer
Answer A: Amber
Amber marks the front and the forward part of the sides of a vehicle, while red marks the rear, so another driver can tell which way the vehicle is facing.